Ash determination dish: a complete guide for accurate testing
2026-11-17
Tangshan High-tech
Article overview
An ash determination dish is a heat-proof vessel for ashing samples. This guide shows food laboratory QA staff in Singapore how to choose, prepare and use an ash determination dish for accurate gravimetric results. It covers materials, a step-by-step SOP, temperatures, calculation, compliance limits and troubleshooting.
Table of contents
- 1. What is an ash determination dish and why does it matter?
- 2. Choosing the right material for your ash determination dish
- 3. Preparing the dish and sample before ashing
- 4. Step-by-step SOP for gravimetric ash determination
- 5. Calculating results: a worked example
- 6. Ashing temperatures, limits and compliance in Singapore
- 7. Troubleshooting, care and sourcing
- 8. Frequently asked questions
What is an ash determination dish and why does it matter?
An ash determination dish is the vessel that carries your sample through the furnace. Its material, mass stability and cleanliness decide whether the final weighing can be trusted. Get it wrong and every decimal place after it is guesswork.
An ash determination dish is a heat-resistant laboratory vessel that holds a weighed sample while organic matter is burned away at a controlled temperature, leaving only the inorganic residue to be weighed. Laboratories also call it an ash content determination crucible, an ashing dish laboratory item, or simply a crucible.
How does the dish fit into proximate analysis?
Ash sits beside moisture, protein, fat and carbohydrate in proximate analysis, which makes the dish one of the core proximate analysis lab consumables. Typical total ash analysis equipment includes an analytical balance readable to 0.1 mg, a muffle furnace, a desiccator and the ash determination dish. The principle is gravimetric: weigh, burn, weigh again. Simple on paper. Demanding at the bench.
Crucible or dish: what is the difference?
Mostly geometry. A crucible is tall and narrow, while a dish is wide and shallow. The wider shape exposes more sample surface to oxygen and speeds up burn-off for fatty or sugary foods. Many methods accept either, and a crucible with lid is common when splashing or sample loss is a concern. Check your validated method before you substitute one for the other.
Why does dish quality affect the result?
Think of the dish as the pan of a very hot balance. Suppose its own mass drifts by 1 mg through glaze flaking, moisture uptake or reaction with sample salts. For a 5 g sample with 0.5% ash (about 25 mg), that drift alone causes roughly a 4% relative error. This is why experienced analysts treat every ash determination dish as a tracked measuring item, not a disposable one. Practical bench experience shows that unexplained scatter between replicates often traces back to the dish rather than the sample.
Choosing the right material for your ash determination dish
Glazed porcelain is the practical default for an ash determination dish in routine food work. Platinum, fused silica and corundum earn their place when sample chemistry, temperature or cost per run changes the calculation. No single material wins everywhere.
Porcelain, silica and quartz options
A porcelain crucible for ash testing is inexpensive, widely stocked and tolerates the 550°C used in many food methods. Its weak point is the glaze, because alkaline ash from fruit, vegetables or seaweed can etch it and slowly change the dish mass. A silica ash dish made of fused silica handles thermal shock better and is lighter, which helps weighing precision. A quartz crucible for muffle furnace use behaves similarly. Prolonged exposure above roughly 1,100°C can cause devitrification, leaving the surface cloudy and brittle. Glaze wear is, in practice, the most underestimated source of drift in routine ash work.
Platinum and corundum for demanding work
A platinum ash determination dish is chemically inert and transfers heat quickly. Laboratories favour it for low-ash, high-value samples such as refined sugar, and for sulfated ash work. Platinum melts at 1,768°C, yet phosphorus, sulfur and reducing metals can alloy with it at high temperature and damage the vessel. Corundum (alumina) is a high temperature ceramic crucible material often chosen for 900°C and above, including as a loss on ignition crucible for mineral samples. It is robust, although dense grades suit constant-mass work better than porous ones.
| Material | Typical working limit | Strength | Main limitation |
|---|---|---|---|
| Glazed porcelain | About 1,100°C | Low cost, easy to source | Glaze attacked by alkaline ash |
| Fused silica / quartz | About 1,100°C | Excellent thermal shock resistance | Devitrifies with long high-heat use |
| Platinum | Melts at 1,768°C | Inert, very stable mass | High cost, sensitive to P, S and metals |
| Alumina (corundum) | About 1,500–1,700°C | Very high temperature stability | Porous grades absorb moisture |
Which dish suits routine food ash content testing?
For routine food ash content testing at 550°C, a 30–50 mL glazed porcelain dish is usually sufficient. Step up to platinum only when throughput, sample value or contamination risk justifies the cost. Where splashing is likely, a crucible with lid cuts sample loss, but leave the lid slightly ajar so oxygen can reach the sample.
Preparing the dish and sample before ashing
Every reliable result starts before the furnace door closes. The dish must be pre-ignited to constant mass, marked permanently and handled only with clean tongs. Skipping this stage is why two analysts so often report different numbers for the same sample.
Pre-ignition and identification
Heat each empty ash determination dish in the muffle furnace at the method temperature for at least 30 minutes, cool it in a desiccator and weigh to 0.1 mg. Repeat until consecutive weights agree within your SOP tolerance, commonly 0.5 mg to 1 mg. Mark the dish with ceramic-safe marking ink, because felt-tip pen burns off. Never touch it with bare fingers, as skin salts leave residue that matters at milligram level.

Sample size and pre-charring
Test portions typically range from 2 g to 5 g for solid foods, adjusted so the final ash is easily weighable but not bulky. High-fat, high-sugar and protein-rich samples tend to swell and flare. Why risk losing material? Evaporate liquids on a water bath, then char solids on a hotplate or under an infrared lamp in a fume hood until smoking stops. Only then does the furnace stage of your ashing dish laboratory routine begin.
Does Singapore's humidity change the routine?
Yes, noticeably. With relative humidity often above 70% through the year, hot ash and porous ceramic reabsorb moisture within minutes of leaving the desiccator. Keep indicating desiccant fresh, limit how often the lid is opened, and weigh every ash determination dish after the same cooling time. An air-conditioned balance room helps, but it does not replace the desiccator.
Step-by-step SOP for gravimetric ash determination
A dependable gravimetric ash determination follows ten controlled steps. The sequence below suits most solid foods at 550°C, but replace the temperature and time with those stated in your validated method.
- Pre-ignite the empty ash determination dish at the method temperature for at least 30 minutes.
- Cool it in a desiccator for 30–45 minutes, then weigh to 0.1 mg and record W1. Repeat until the weight is constant.
- Weigh 2–5 g of homogenised sample into the dish and record the sample mass W2.
- Dry liquids on a water bath, then char solids on a hotplate in a fume hood until smoking stops.
- Place the dish in the muffle furnace with tongs, spacing dishes so air can circulate.
- For fatty samples, hold at about 250°C for 30–60 minutes before raising the temperature. This reduces flaring.
- Ash at the target temperature (for example 550°C) for 4–6 hours, or overnight, until the residue is white or light grey.
- Switch off and let the furnace fall below roughly 250°C before opening. Move the dish into a desiccator with pre-warmed tongs.
- Cool for the same period used in step 2, then weigh and record W3.
- Re-ash for 30–60 minutes and reweigh until consecutive weights agree within tolerance. Record all values.
Heating programme and timing
Furnace set-points are not always actual temperatures. Verify the chamber with an independent calibrated thermocouple at least annually, or as your quality system requires, and map hot spots near the door. Many labs ramp rather than plunge dishes into a hot chamber, because rapid heating can crack porcelain and cause sample ejection. A slower ramp costs time but protects both the sample and the dish.
Cooling and weighing
Consistency matters more than speed here. Transfer, cool and weigh each batch on the same schedule, and avoid loading too many hot dishes into one desiccator, since the warm air can lift the lid and raise internal humidity. Use a balance with a draught shield and record the temperature of the balance room when weighing.
What if black specks remain after ashing?
Black specks mean unburnt carbon. Cool the dish, add a few drops of deionised water or a small amount of hydrogen peroxide to loosen the residue, dry gently, and re-ash. Some methods allow dilute nitric acid as an ashing aid, but follow the validated method and handle acids in a fume hood. Of course, there are samples, such as high-salt or high-phosphate foods, where carbon is trapped inside fused ash. Lowering the temperature is then better than raising it.
Calculating results: a worked example
Ash percentage equals the mass of ash divided by the mass of sample, multiplied by 100. Only three weights are needed from the ash determination dish: empty mass, sample mass and final mass.
The formula
Ash (% w/w, as-is) = (W3 − W1) ÷ W2 × 100, where W1 is the pre-ignited dish mass, W2 the test portion mass and W3 the dish plus ash at constant mass. To express ash on a dry basis, divide the as-is value by (1 − moisture fraction). Always state the basis in your report, because a flour result of 0.6% as-is and 0.7% dry are both correct but not interchangeable.
Illustrative case: plain flour in a QA lab
The figures below are a hypothetical teaching example, not measured data from a real laboratory. They show how food ash content testing is recorded for plain wheat flour in a porcelain dish at 550°C.
| Parameter | Value |
|---|---|
| Pre-ignited dish mass (W1) | 32.4510 g |
| Sample mass (W2) | 5.0012 g |
| Dish + ash, constant mass (W3) | 32.4812 g |
| Ash mass (W3 − W1) | 0.0302 g |
| Ash, as-is | 0.0302 ÷ 5.0012 × 100 = 0.60% |
| Ash, dry basis (moisture 12.0%) | 0.60 ÷ 0.880 = 0.69% |
Does your result look reasonable?
A sanity check against published composition data catches gross errors. The approximate values below are drawn from USDA FoodData Central entries. Real products vary by cultivar, processing and fortification, so confirm against the current database.
| Food (per 100 g) | Approximate ash (g) |
|---|---|
| Wheat flour, white, all-purpose | 0.5 |
| Wheat flour, whole grain | 1.6 |
| Rice, white, raw | 0.6 |
| Milk, whole | 0.7 |
| Chicken breast, raw | 1.0 |
Ashing temperatures, limits and compliance in Singapore
There is no single ashing temperature. The correct value depends on the product and the method you are accredited for, and published standards range from about 550°C to 900°C. Using the wrong temperature with an otherwise perfect ash determination dish still produces a non-compliant result.
Which temperature should I use?
The table lists commonly cited conditions from international standards. Editions are revised, so check the current version before updating your SOP in 2026.
| Matrix | Typical ashing temperature | Reference method |
|---|---|---|
| Cereals and flour | 900°C | ISO 2171 |
| Meat and meat products | 550°C | ISO 936 |
| Spices and condiments | 550°C | ISO 928 |
| Animal feed | 550°C (ISO) / 600°C (AOAC) | ISO 5984 / AOAC 942.05 |
Note that the 900°C cereal method needs a dish that survives that heat, so an alumina or high-grade porcelain item is more suitable than an ordinary glazed dish. The general idea behind ash determination is well documented, and the principle is shared across these methods:
Paraphrased from the common principle of AOAC and ISO ash methods: ash is the inorganic residue left once organic matter has been removed by heating, so the result depends on temperature, time and the vessel used.
What limits apply to my product?
Ash limits come from product specifications, customer contracts, Codex commodity standards or the Singapore Food Regulations, depending on the food. Many products have no statutory ash limit at all. Rather than quoting a number from memory, cite the exact clause and edition in your report, and consult the Singapore Food Agency (SFA) or your regulatory team if the applicable limit is unclear.
Accreditation and records
Laboratories seeking recognition under ISO/IEC 17025, for example through SAC-SINGLAS, should keep records for each ash determination dish: identification, pre-ignition history, inspection dates, and balance and furnace calibration. Traceability turns a number into evidence. Auditors tend to ask first about constant-mass criteria and temperature verification, so have those ready.
Troubleshooting, care and sourcing
Most ash errors fall into three groups: contamination or moisture gain (results too high), volatile loss or fusion (results too low), and equipment damage. Recognising the pattern saves repeat runs. A good ash determination dish used carefully can serve many cycles.
Common faults and their causes
- High and drifting results: incomplete constant mass, moisture uptake after cooling, or a contaminated dish.
- Low results: loss of volatile chlorides, sodium, potassium or phosphorus when the temperature is too high or heating is too aggressive.
- Glassy, fused ash: low-melting salts trapping carbon. Reduce the temperature or extend the time.
- Cracked dishes: thermal shock from hot dishes placed on cold benches or loaded into a very hot chamber.
Cleaning and service life
Soak used dishes in warm dilute hydrochloric acid, rinse thoroughly with deionised water, dry, and re-ignite before reuse. Avoid abrasive pads that scratch the glaze. Retire any dish showing crazing, pitting or a mass that no longer stabilises. Platinum should be cleaned and reconditioned according to the maker's guidance, and never heated in direct contact with a reducing flame.
How to choose a laboratory crucible supplier in Singapore
When evaluating a laboratory crucible supplier Singapore buyers rely on, request a datasheet that states material, glaze, capacity, dimensional tolerance and maximum working temperature. Ask about lot traceability, lid fit, lead time and after-sales support. Corundum ceramic crucibles and tubes are one product category some suppliers carry for high-temperature work. Judge them by the specification sheet, not catalogue claims alone, and validate a trial batch against your existing dishes before changing routine practice.
Accurate ash testing comes down to discipline: choose a dish suited to the matrix, pre-ignite it to constant mass, follow the temperature in your validated method, and weigh under consistent conditions. A well-chosen and well-maintained ash determination dish removes a major source of uncertainty before the furnace is even switched on. Review your SOP against the current standards, and consult your accreditation body or a qualified colleague for method-specific decisions.
Frequently asked questions
Q: What is an ash determination dish used for?
A: An ash determination dish holds a weighed food or feed sample while it is heated in a muffle furnace. Organic matter burns away, and the remaining inorganic residue is weighed to calculate total ash content.
Q: Is a porcelain dish good enough for ash testing?
A: For most routine food methods at about 550°C, glazed porcelain is suitable and economical. Use platinum, silica or alumina when samples attack the glaze, when very low ash levels are measured, or when temperatures reach 900°C.
Q: How do I know the ashing is complete?
A: The ash should look white or light grey without black carbon specks, and consecutive weighings after re-ashing should agree within your method tolerance, commonly 0.5 mg to 1 mg. Both checks should be met.
Q: Why must the dish be pre-ignited before use?
A: Pre-ignition removes moisture and volatile contaminants, so the empty dish mass is stable. Without a constant starting weight, any mass change during ashing would be wrongly counted as sample ash.
Recommended news